Swiss Plus SRVC-3021 21.6 V Lithium Cordless Vacuum Cleaner User Manual

Using the electrical appliance, the following basic precautions should always be followed:

1. This is a dry vacuum cleaner, do not use it to suck liquid to avoid being damaged.
2. Do not immerse the charger or vacuum cleaner into the water for cleaning to avoid any risk.
3. Do not use appliance on or near a hot gas or on a heated oven.
4. Make certain that the ventilation slits of the appliance are not covered in case affect radiating heat.
5. Do not use the appliance to suck flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
6. Make sure that your outlet voltage corresponds to the voltage stated on the rating label of the charger.
7. Do not use the appliance with damaged charger, cord or plug.
8. The appliance can only be powered by the charger provided. Do not use the charger to charge any other appliance.
9. Before cleaning, cut off the power source of charger to avoid electric shock.
10. Do not operate the appliance if the cord of charger is damaged or after malfunction or has been damaged in any manner. Return appliance to an authorized service facility for examination, repair or adjustment. Do not detach the battery for other than its intended use.
11. The battery must be disposed properly if it can no longer be used. Never scrap it into fire as explosion may occur.
12. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliances by a person responsible for their safety.
13. The use of accessories not recommended by the manufacturer may cause injuries to persons.
14. Do not operate the appliance for other than its intended use.
15. Do not use outdoors.

The body, floor brush, charger, charger stand, adapter, small hair brush, and flat suction spout shall be packed separately for convenient transportation and storage, as this vacuum cleaner is of a large size. The users shall install the appliance by following the instructions below when using it for the first time.

• Install the body and floor brush Insert the floor brush into the body by following the arrow shown in A. When the release button locks the body, rotate the handle and insert it into the body(1). If you need to fold the handle, rotate the handle release button (3). FIG. A FIG. B

Insert the charger into the charger stand (see Fig. C). After that, use the attached screws to mount the entire unit onto the wall or place it on a horizontal surface. FIG. C FIG. E FIG. D

Operating the appliance: The appliance has two switches: the power switch (1) and the speed switch (2) (see Fig. F). Press the power switch (1) to start the motor. The floor brush indicator will light up, and the appliance will begin operating. To change to a lower power mode, press the speed switch (2) once. Press the speed switch (2) again to switch to the higher power mode. To stop the appliance, press the power switch (1) again. During use, monitor the battery level indicators (3). These indicators will turn off gradually as the battery depletes. The appliance will automatically shut down when all indicators are off.

FIG. F

To detach the sub-unit, press the release button (4) (see Fig. G), then hold the handle and pull it out in the direction of the arrow. Next, press the sub-unit power switch to start its operation. To turn it off, press the same switch again. If you need to use the small hair brush, insert it into the suction nozzle of the sub-unit as shown in Fig. H, and then activate the sub-unit again. If you need to use the flat suction spout, insert it into the suction nozzle of the sub-unit as shown in Fig. J, and then activate the sub-unit again. I H K J G

1. Fix the charger by following the diagram. Insert the small end of the adaptor into the charger stand as shown in Fig. L.
2. Plug the large end of the adaptor into a power outlet, and ensure the power source is connected properly (see Fig. M). L FIG. M

3. Lift the appliance and place it onto the charger. Align the socket on the appliance body (1) with the charger stand (2) as shown in
4. (Fig N). At this point, the battery level indicator will turn on, and the appliance will enter charging mode. All the charging indicators will light up once charging is complete. NOTE: The appliance cannot be used during the charging process. FIG. N FIG. O

1. Detach the accessory from the sub-unit. Then, press the left and right release buttons (2) on the dust cup (1 ) to separate it from the sub-unit.

1. FIG. P
2. Grasp the filter handle (3) and remove the filter assembly from the dust cup. Empty the dust cup and rinse it with water. Finally, wipe off any remaining water from the dust cup. FIG. R FIG. Q

3. Grasp the filter handle (3) and rotate it anticlockwise to remove the HEPA filter (5). Then, empty the filter cover (6) and rinse it with water. Finally, wipe off any remaining water from the filter cover. FIG. T

3. FIG. S
4. Clean the HEPA filter (5) with water if the appliance is not working efficiently, and make sure to dry it completely after cleaning. NOTE: The HEPA filter and other spare parts can be purchased
5. from vacuum cleaner retailers. After cleaning the dust cup assembly, first install the HEPA filter into the filter cover. Then insert both into the dust cup. Finally, install the dust cup back into the sub-unit.

5. FIG. U
6. If hair found on the floor brush, press the roll brush release tab (7) as shown below to open the roll brush cover, and then remove the roll brush (8). FIG. V FIG. X

7. Scratch along the locating slot of the roll brush with a blade to cut and clean the air. After it, install the floor brush well again and close the roll brush cover. NOTE: It is recommended to clean the duct cup after every use. If the HEPA filter is blocked due to the accumulation of dust, please clean or replace it in time. The electric roll brush may be wrapped with some hair or other floccule after long time use, so please clean it in time to make the appliance work efficiently.

7. FIG. Y