Swiss Plus SS-1024 Steam Generator Iron User Manual

1. When using electrical appliances basic safety precautions should always be followed.
2. Check that the voltage indicated on the rating plate corresponds with that of the local voltage before connecting the appliance to the mains power supply.
3. Children aged above 12 years and people with reduced physical, sensory or mental capabilities or lack of experience or knowledge can use this appliance with supervision or instruction given.
4. Keep the appliance and its power supply cord out of reach of children.
5. The product can only be used with grounded socket.
6. This appliance contains no user-serviceable parts. If there is any leakage or if it has been dropped or damaged, only a qualified electrician should carry out repairs. Improper repairs may place the user at risk of harm.
7. Keep the appliance and its power supply cord away from hot/heat or sharp edges that could cause damage.
8. Do not immerse the appliance in water or any other liquid.
9. Do not operate the appliance with wet hands.
10. Do not switch on the appliance unattended while connected to the mains power supply.
11. Do not switch off the appliance directly by unplug the mains power; switch off with button and remove the plug by hand.
12. Steam on people or animals are straightly never allowed.
13. Do not direct steam towards equipment containing electrical components.
14. Do not use the appliance in an enclosed space filled with vapour given off by oil-based paint thinners, some moth-proofing substances, flammable dust or other explosive or toxic vapours.
15. Do not use any accessories other than those supplied.
16. Do not touch any sections of the appliance that may become hot or the heating components of the appliance, as this could cause injury.
17. Do not use the appliance after a malfunction or if it is leaking.
18. Always unplug the appliance after use and before any cleaning or user maintenance.
19. Always ensure that the appliance has cooled fully after use before performing any cleaning or maintenance.
20. Always use the appliance on a stable, heat-resistant surface, at a height that is comfortable for the user.
21. Use of an extension cord with the appliance is not recommended.
22. This appliance is intended for domestic use only. It should not be used for commercial purposes.

Before using the appliance for the first time, ensure that it is switched off and unplugged from the mains power supply. Clean the exterior surface of the Steam Generator Iron with a dry, soft, damp cloth. Note: Make sure the cloth is dry and clean, do not immerse with water or others liquid. A slight odour and small amount of smokmay be emitted during first usage. This consider normal.

1. Fill the water tank with clean, filtered water up to the MAX line. Using filtered water is important, as tap water containing dirt or sediments may cause the steam pump to clog and prevent steam production.
2. Before operating the Steam Generator Iron, ensure it is
3. EN: Check that the steam control is set to the “MIN” position.
4. Switch on the appliance and set the temperature and steam button to the level corresponding to the desired temperature
5. The power indicator light will turn on. During heating, the steam indicators on the control panel will flash. Once the appliance reaches the correct temperature, the indicator becomes steady. This process takes about 60 seconds and is controlled electronically.
6. EN: Wait until the pilot light turns off, which indicates that the appliance has reached the proper temperature.
7. Press and hold the steam button for 10 seconds. During use, the pilot light may flash again to indicate that the heating element is maintaining the temperature. Note: It is advised to use clean tap water instead of de-ionized water, as de-ionized water may affect internal sensors and cause the pump to operate incorrectly. Warning: Do not fill the water tank with hot water. Warning: Never add descaling agents, fragrances, alcohol, or detergent products into the appliance, as these may damage the device or make it unsafe for use.

For the first time usage, it is recommended to iron a plain cloth for testing purpose to make sure the Steam Generator Iron is working with correct temperature. Ensure that it is done without using the steam setting.

1. Fill the water tank according to the instructions. (Important! Use Filtered Water)
2. Plug in and press the Power button, then rotate the temperature control clockwise. Also rotate the steam output control clockwise: level 1 for dry iron, level 2 for moderate steam, and level 3 for maximum steam.
3. To increase or decrease the temperature of the soleplate, rotate the temperature control clockwise or anticlockwise. The temperature indicator light will illuminate while heating and will switch off when the device is ready to use.
4. Select the steam setting by pressing and holding the steam button. The steam setting can be switched off at any time by releasing the steam button.
5. After use, rotate the temperature control to the ‘MIN’ position, turn back the steam output control, switch off the power button, and unplug the Steam Generator Iron from the mains.

The Steam Generator Iron must be set at a minimum 2-dot heat setting to produce steam. When not in use, ensure that it is rested on the base unit. Do not iron one particular area for long periods of time, as this will damage the fabric. The soleplate becomes very hot during use; do not touch it Warning: Keep the appliance away from flammable material. Warning: Danger of scalding. Caution: The appliance emits very hot steam; always exercise extreme caution during use.

1. Hang up the item to be vertically steamed.
2. Fill the water tank according to the instructions.
3. Rotate the temperature control until a minimum 3-dot or max heat setting; the higher the temperature, the more powerful the steam. Rotate the steam output control clockwise and choose level 2 or 3 for vertical steaming and flat ironing.
4. Holding the Steam Generator Iron approximately 5–10 cm away from the fabric, press and hold the steam button, or use the steam lock for continuous steaming

Important Advice! If a garment has various kinds of fibers, select the temperature for the fiber that requires the lowest temperature. (Example: For 60% polyester / 40% cotton, select the polyester temperature.)

1. Always start on a lower heating setting and work up to a higher one whenever needed; it takes less time for the Steam Generator Iron to heat up than it does to cool down.
2. It is advised that the steam button is used for short bursts rather than prolonged periods of time. This can prevent water dripping from the steam holes and can reduce the frequency of needing to refill the water tank.
3. Before each use, check the care labels on the fabrics to be ironed so that the correct temperature setting is selected.

• Before attempting any cleaning or maintenance, always unplug the Steam Generator Iron from the mains power supply and allow it to cool for approximately 30 minutes.
• Drain the remaining water from the water tank to prevent it leaking during cleaning.
• Wipe the Steam Generator Iron with a soft, damp cloth and dry thoroughly.
• To remove any build-up around the steam holes, use a cotton wool tip dampened with methylated spirits. Wipe off the methylated spirits with a soft, damp cloth and dry thoroughly.
• Do not immerse the Steam Generator Iron in water or any other liquid.

1. Fill the tank with approximately 1 liter of water (Don’t put vinegar, perfume or other descaling agents into the water tank.)
2. Plug in the ironing system and set the temperature control to MIN and Steam Clean program.
3. Hold the iron vertically over the sink and press the steam button for 1 minute to pump the water from the tank to the iron.
4. Increase the iron’s temperature setting to number 2.
5. Place the iron horizontally over the sink, keep pressing the steam button and gently rock the iron backwards and forwards for 1 minute.
6. Unplug the ironing system from the mains supply and immediately rub the soleplate with a damp cotton cloth folded several times. (Never use scouring pads or chemicals.)

• Repeat the cleaning process at least twice.
• We recommend performing the process once a month to prolong the service life of the ironing system. If the water in your area is very hard or you notice limescale coming out through the soleplate during ironing, use this function more often.

• Before storing the Steam Generator Iron, ensure that it has cooled and dried thoroughly.
• Check that the water tank is empty before storing.
• Clamp the cord and steam pipe in the base storage; never clamp it tightly as this could cause damage.
• Position the Steam Generator Iron onto the rubber support of the base unit; this will help to prevent the nano ceramic soleplate from getting scratched.

To reduce the risk of fire, electric shock or injury, unplug the product from the mains power supply before troubleshooting.