Swiss Plus SSI-1022 Steam Iron User Manual

1. Before using the device for the first time, ensure that the voltage rating on the device corresponds with the local voltage supply.
2. This device must only be used with a grounded socket.
3. When leaving the device, even for a short period, turn it off, place it on its stand, and always unplug the power cord.
4. The device will become hot during use; therefore, avoid touching it and do not place it near flammable materials.
5. Before filling the device with water, always unplug it from the power supply.
6. Never immerse the device in water or any other liquids.
7. 7.If you notice any damage to the cord or defects, only send it for repair to an authorized service center.
8. Using water containing mineral deposits may cause the steam holes to block; therefore, it is recommended to use distilled water.
9. Do not use any liquids or chemicals in the water.
10. The steam emitted from the device is hot and can be dangerous; never direct the steam toward people or animals.
11. This device is not intended for use by individuals (including children) with physical, sensory, or mental limitations, or by those who are inexperienced or unaware, unless they are supervised by a responsible person who ensures their safety or provides instructions on how to use the device.
12. Children must be supervised to ensure they do not play with the device.
13. The device must be placed and used on a stable and heat-resistant surface.
14. When placing the device on its stand, ensure that the surface it rests on is stable.
15. The device should not be used if it has been dropped, if there are visible signs of damage, or if it is leaking. To prevent any accidents, all repairs, including the replacement of the power cord, should only be carried out by the authorized service center or authorized SwissPlus representatives.

1. The iron has been greased, and as a result, the iron may slightly smoke when switched on for the first time. After a short while, this will cease.
2. Before using for the fist time, remove any sticker or protective foil from the soleplate. Clean the soleplate with a soft cloth.
3. Keep the soleplate smooth: avoid hard contact with metal objects.

Make sure iron is unplugged and the temperature dial is in the MIN position. Place iron on the heel rest, tilt forward approximately 45 angle and pour water into the water-filling cover to the MAX position of the water tank.

“Burst of Steam” can also be applied when holding the iron in vertical position, this is useful for removing creases from hanging clothes,Curtains etc.

1. Set the Steam Selector to position O(=No Steam)
2. As per washing label of various clothes, set the correct ironing temperature to begin a ironing.

At any temperature by pressing the spray button a couple of times, the laundry can be damped down. Ensure that there is enough water in the water tank.

1. Fill in the water with water tank as per the water-filling methods. Plug the appliance in the socket.
2. If only set Fabric Select Dial to MAX position as per the temperature
3. indicator, steam iron will be available, otherwise water may leak from the soleplate. It indicates that the temperature has been ready until the power
4. indicator light goes off. Set the Steam Selector correctly, increase steam output by pushing
5. the Steam Selector back and decrease steam output by forward.

This function works well for tough wrinkles and heavy fabrics. By pressing “Burst of Steam Button”,an intense burst of steam is emitted from the soleplate, this can be very useful when removing stubborn creases. The burst of steam facility can be used only while ironing with high ironing temperature. For optimal result, there should be 5 seconds rest between presses of the steam button. To prevent leaking water from the soleplate does not press the steam button continuously for more than 5 seconds.. Also allow at least one minute interval before applying this burst of steam function.

With a bimetal assembled inside the iron, which can close the steam when the iron soleplate becomes very low, so water leakage will never happen with this features.

With a small filter built-in,which can make hard water soft, thus preventing any calc or flake accumulated on the surface of soleplate,this features can prolong the life of the iron for long use.

Use the self-cleaning function once every two weeks. If the water in your area is very hard (i.e, when flakes come out of the soleplate during ironing), the self-cleaning function should be used more frequently.(. Make sure the appliance is unplugged, set the Steam Selector to steam level “O”, fill the water tank to the MAX position, do not put vinegar or other dealing agents in the water tank., select the maximum ironing temperature, put the plug in the wall socket, unplug the iron when the power indicator lighter has gone off, hold the iron over the sink, press the self-cleaning button , at this time, the self-cleaning begin works, then shake the iron to and fro. Steam and boiling water will come out of the soleplate, impurities and flakes )if any( will be flushed out. Repeat the self-cleaning process if the iron still contains a lot of impurities. After the self-cleaning process, put the plug in the wall socket and let the iron heat up to allow the soleplate to dry, unplug the iron when it has reached the set ironing temperature, move the hot iron gently over a piece of used cloth to remove any water stains that may have formed on the soleplate, let the iron cool down before you store it. down before you store it.

Before cleaning, remove the plug from the socket and allow the iron to cool down sufficiently.

1. Wipe off the soleplate with a damp cloth and a non-abrasive (liquid) cleaner.
2. If the fiber is adhered to the soleplate, use a damp cloth with vinegar to wipe off the soleplate.
3. Never use strong acid or alkali in order to avoid damaging the soleplate.
4. If the scale blocks the steam hole, please remove the scale with toothpick; do not damage the surface of soleplate.
5. Stand the iron on its end and let it cool down sufficiently, and meantime pour any remaining water out of the box, set the dry/steam selector to position “O”.